Z-Wave Plus Z-Wave.Me Z-Uno Shield

In stock
SKU
ZME_Z-Uno-SH
As low as $110.39
Желаемая дата доставки
  

The first and only easy to use developer board that allows you to create your own Z-Wave device

  • Z-Uno Shield Configurator allows to create:
    • Dimmers
    • Switches (and Sirens, Valve controls, Door locks)
    • Sensors
    • Thermostats
  • The perfect companion for you RaZberry gateway
  • Compatible with other controllers like Fibaro Home Center 2, Fibaro Home Center Lite, Vera Edge and Zipato Zipabox
  • Control any Arduino compatible peripherals
  • Z-Wave Plus Certified
  • For installators 

Z-Uno Shield For installers

Z-Uno ShieldZ-Uno Shield is an extension board for Z-Uno for easy installations. It requires no soldering and no programming — configure, wire and include in the network.

Z-Uno Shield comes in DIN-rail case or Sealed case and have terminal strip for easy connection. An easy-to-use configuration tool will help you to define the behaviour of your Z-Uno Shield depending on the connected devices.

Being a Z-Wave Plus certified device, Z-Uno is the perfect companion for you RaZberry gateway. Z-Uno is compatible with other controllers too.

Z-Uno is very powerful but requires some knowledge of schematics and programming. To help users and installers to work with Z-Uno we have created the Z-Uno Shield. Z-Uno Shield is a multifunctional DIN-rail smart home device based on Z-Uno. It implements most useful features of Z-Uno and requires no soldering and no programming.

No soldering required!

Z-Uno Shield is very easy to wire. It allows to connect many smart home actors and sensors out of the box:

  • One 0-10 V analog output — control industrial dimmers
  • Up to four PWM or siwtch outputs (up to 5 A per channel) — control contactors, switches, halogen bulbs or LED strips
  • Up to eight digital 0/3 V inputs or outputs — connect various low voltage digital senors and actors
  • Up to four digital 0/3, 0/5 or 0/12 V digital or analog inputs — connect industrial 10 V sensors or any Arduino-compatible sensor
  • RS485 or UART — for industial meters
  • OneWire — for DS18B20 or other sensors

For those who still want to solder something there is a bread board for your additional components.

No programming required!

We have created the Z-Uno Shield Configurator that will not only help you to wire your Z-Uno Shield correctly, but will also write the Z-Uno sketch for you. Most popular cases are covered by this tool. You can still modify the generated code or write your own sketch.

Z-Uno Shield Configurator allows to create:

  • Dimmers
  • Switches (and Sirens, Valve controls, Door locks)
  • Sensors
  • Thermostats

Casing

Z-Uno Shield comes in DIN-rail case or Sealed case and have terminal strips for easy connection.

Unveil your imagination to create:

  • battery powered in-wall remote switch
  • rotary dimmer control
  • temperature/soil humidity/luminosity/voltage/distance or any other sensors as well as dry contact sensor or tick counter
  • low voltage switch
  • IR blaster
  • LED driver
  • motor driver
  • battery powered keypad
  • converter from any protocol to Z-Wave (using SPI/UART/I2C/1-wire bus)
  • ... or any other device you dreamed about

Make your own Z-Wave device:

  • control any Arduino compatible peripherals
  • define your own logic by modifying your sketch
  • use Arduino IDE and language to write and upload sketches
  • easy to use
  • requires no knowledge of Z-Wave protocol
  • complete DIY solution

Hardware specification: 

  • 28 kB Flash memory for your sketches
  • 2 kB RAM available
  • Z-Wave RF transmitter at 9.6/40/100 kbps
  • 26 GPIO (overlaps with special hardware controllers)
  • 4 ADC
  • 5 PWM
  • 2 UART
  • 1 USB (serial port)
  • 16 kB EEPROM
  • 1 SPI (master or slave)
  • 4 IR controllers, 1 IR learn capability
  • 1 TRIAC/ZEROX to control dimmer
  • 3 Interrupts
  • 1 Timer 4 MHz
  • I2C (software)
  • 1-Wire (software)
  • 8x6 Keypad Scanner (software)
  • 2 service LED, 1 service button
  • 1 user test LED

Power modes: 

  • USB 5 V, external 5 or 3 V, external 7-18 V or battery (via MU-2F connector, included)
  • always on, sleeping or FLiRS (Frequently Listening)

Z-Wave supported features: 

  • Z-Wave Plus compliant
  • all Z-Wave frequencies (check availability)
  • out of the box support of AES 128 bit Security
  • upgrade via USB or radio (Z-Wave OTA)
  • Multichannel (32 channels)
  • 5 Association groups
  • controls switches, dimmers, door locks and scenes
  • works with gateways and/or directly with other Z-Wave devices

Channel types: 

  • Binary Switch
  • Multilevel Switch
  • Color Switch
  • Binary Sensor
  • Multilevel Sensor
  • Meter

Dimensions: 

  • L×W×H: 39×20×16 mm (PCB dimentions with all compinents)
  • L×W×H: 39×20×7 mm (PCB dimentions with PLS and battery connectors removed)
  • Antenna lenght: 86 mm (89 mm with isolation), can be bent to better fit your dimensions
  • Wigth: 7 g

Antenna: 

  • Antenna type: wire antenna 86 mm for 865-870 MhZ
  • Alternative antenna: optional u.fl connector can be soldered (to RF2 pads)

Electrical characteristics: 

  • Digital pin in logical 1: > 2.1 V, leakage current 10 μA
  • Digital pin in logical 0: < 0.9 V, leakage current 10 μA or 40–120 μA (with internal pull-up enabled)
  • Internal pullup resistor: 15–20 kΩ (at +25°C)
  • Digital pin out logical 1: > 2.4 V, max current sourcing 8 mA (16 mA for digital pins 3-6)
  • Digital pin out logical 0: < 0.4 V, max current sinking 8 mA (16 mA for digital pins 3-6)
  • Total max current sourcing from GPIO pins: 120 mA
  • Power consumption on 3.3 V:
    • in always listening mode 50 mA
    • in sleep mode 1 mA (about 7 μA if DC-DC is turned off by unsoldering R12)
    • in FLiRS mode 1 mA (about 70 μA if DC-DC is turned off by unsoldering R12)
  • Power consumption on 5 V: in always listening mode ∼ 30 mA (can be lowered by using external switching DC-DC)
  • Power consumption on 7–18 V: in always listening mode ∼ 35 mA (can be lowered by using external switching DC-DC)
  • DC-DC installed:
    • 7–18 V → 5 V: NCP1117ST50T3G, max current sourcing from 5V pin 900 mA
    • 5 V → 3 V: MCP1700, max current sourcing from 3V pin 200 mA

See Z-Uno power supply schematics for more info.

 — these features will be implemented in near future

Deeper insight

Know more about Z-Uno internals.

Pinout

Wireless range

The better the wireless range, the more reliable the product, and device offers a class-leading antenna. Optimised for reliability, this tiny unit  can wireless communicate over 150 metres.

Gen5

The best antenna. The best Z-Wave. Device is built upon Z-Wave Plus and leading Gen5 technology to offer you the fastest response times and optimal battery life between recharges.

Secure security

If you’re using a sensor for security you want its communication to be secure. That’s why unit utilises AES-128 wireless data encryption to keep it secure from prying eyes and hackers.

Wireless updates.

Whether used for home intelligence or security, you want your device to always stay up to date. Whenever firmware udpdates are made for it, you’ll be able to upgrade unit via Microsoft Windows or select Z-Wave gateways.

Technical Specification

  • MODEL NUMBER
    • ZME_Z-UNO-Shield
  • HARDWARE
    • Z-Wave Chip 500 series
  • COMMUNICATION PROTOCOLS
    • Z-Wave Plus
  • DIMENSIONS
    • Packing size:5x2x5 cm (LxWxH)
    • Base size:
      • LxWxH: 39x20x16 mm (PCB dimentions with all compinents)
      • LxWxH: 39x20x7 mm (PCB dimentions with PLS and battery connectors removed)
  • CERTIFICATIONS
    • CE, Z-Wave
  • POWER SUPPLY
    • Input: USB 5 V, external 5 or 3 V, external 7-18 V or battery (via MU-2F connector, included)
  • POWER CONSUMPTION
    • up to 1W
  • RADIO SIGNAL POWER
    • up to 1mW
  • RANGE
    •  up to 200m (outdoors) and 100m (indoors)
  • OPERATIONAL TEMPERATURE
    • 0-50°C
  • IP CODE
    • IP20

Package content

  • Unit
  • User manual

Additional Info

Z-Wave Association Capabilities

Model: Z-Uno (v3)

Z-Wave Certification Number: ZC10-16065104


Group ID

Maximum Nodes

Description

1 5 Z-Wave Plus Lifeline. All unsolicited reports on all channels are sent to this group
2 5 Configurable group to send on/off, dimming or scene activation. See product reference
3 5 Configurable group to send on/off, dimming or scene activation. See product reference
4 5 Configurable group to send on/off, dimming or scene activation. See product reference
5 5 Configurable group to send on/off, dimming or scene activation. See product reference
6 5 Configurable group to send on/off, dimming or scene activation. See product reference

Z-Wave Configuration Capabilities

Model: Z-Uno (v3)

Z-Wave Certification Number: ZC10-16065104


Parameter Number

Parameter Size

Parameter Name

Parameter Values

2 1 Blink with service LED during operation 0
(Default)
Dont blink
  1 Blink

Z-Wave Command Classes

Model: Z-Uno (v3)

Z-Wave Certification Number: ZC10-16065104


Supported Command Classes
 
        Association Group Information V1
        Association V2
        Basic V1
        Configuration V1
        Device Reset Local V1
        Firmware Update MD V3
        Manufacturer Specific V2
        Multi-Channel V4
        Multilevel Switch V1
        Notification V5
        Powerlevel
        Security V1
        Sensor Binary V2
        Sensor Multilevel V7
        Version V2
        Z-Wave Plus Info V2
 
 
Controlled Command Classes
 
        Basic V1
        Multi-Channel V4
        Multilevel Switch V1
        Security V1

User manual

Guides

More Information
Technology Z-Wave+
Z-Wave Plus: Yes
Z-Wave Hardware Platform WML-C85
Z-Wave Library Type Enhanced 232 Slave
Z-Wave Device Type On/Off Power Switch
Z-Wave Role Type Always On Slave
Manufacturer Z-Wave.Me
Power source USB
Type of controller adapter Microchip
Usage Compliment Core System
App Compatibility iOS, Android
Form factor Other
Write Your Own Review
You're reviewing:Z-Wave Plus Z-Wave.Me Z-Uno Shield
Your Rating
Copyright © 2016 Swinestudio. All rights reserved.