Aeotec Recessor for Multisensor 6

In stock
SKU
AEO_DSE010
$21.29

Install MultiSensor 6 on a ceiling or wall cavity with recessor

  • Designed for Aeon Multisensor 6
  • Easy Wall or Ceiling installation
  • Extrudes only 1.2 cm space

Recessor for Multi Sensor 6

Smart sensor.

Invisible sensor.

MultiSensor 6 is smartest and most subtle Z-Wave sensor available. Within its impossibly small design it features 6 different Z-Wave sensors, effortlessly monitoring a room and making your connected home all the more intelligent.

With Recessor, the impossibly small MultiSensor 6 becomes even more smaller. In fact, it becomes nearly invisible, sitting only 0.04 inches within a room.


1.2cm of sensor.

We like things small. We prefer them invisible. Recessor offers the best of both. It lets MultiSensor 6 monitor 6 different points of intelligence in a room, and it lets it do it without reducing its accuracy or functionality.

Self-holding

Itself only 4.4cm deep, Recessor snaps in place courtesy of 2 ingenious retainingspring clips. Those same springs of course allow for Recessor and MultiSensor 6 to be removed at any time without damaging your ceiling or wall.

Subtle installation.

Whether it’s within a wall or in a ceiling cavity, Recessor lets MultiSensor 6 work its magic subtly.

wall wall
wall
Ceiling installation.

Monitor a full room with MultiSensor 6 using Recessor to install it within your ceiling.

wall
Wall installation.

Use MultiSensor 6 as a beam sensor by installing it within a wall cavity using Recessor.

Still perfectly powered.

The perfect option of running your MultiSensor 6 with mains or battery power continues with Recessor.

Recessor has been designed to allow for a power cable to still be connected to MultiSensor 6 so that it can run without batteries. Recessor has also been designed so that it can be easily removed to allow for MultiSensor 6’s batteries to be changed every 2 years.


wall

Still precise.

Recessor doesn’t just convert MultiSensor 6 into a Z-Wave ceiling or beam sensor, it converts it into a precise sensor.

Once recessed, your MultiSensor 6 can be angled up to 30ºwithin Recessor, fine tuning its measurements and readings to be just where you need them.

Simple to install

After 3 easy steps, you’ll have Recessor installed within your wall or ceiling space.

wall wall
Make a 75mm/3″space for Recessor. Lock MultiSensor 6 in place.
wall wall
Insert Recessor-it’ll hold itself in place. That’s it!

More about MultiSensor 6.

wallMultiSensor 6 is more than just an invisible sensor, it’s a really clever. From its 6 different sensors to its precession engineering, it’s the sensor that means that the smart home is finally smart.

You can find out more about MultiSensor 6 here.

wall
technical-specifications

Technical Specification

  • DIMENSIONS
    • Packing size:110x110x50 mm (LxWxH)
    • Base size: 100x100x44 mm (LxWxH)
  • CERTIFICATIONS
    • CE
  • IP CODE
    • IP20

Package content

  • Unit:
    • Sensor Unit. 
    • Battery Cover.
    • Back Mounting Plate. 
    • Double-Sided Tape.
    • Screws (x3). 
    • mICRO USB cable
  • User manual

Z-Wave Specification

Z-Wave Association Capabilities


Group ID

Maximum Nodes

Description

1 5 The MultiSensor supports 1 association group. Group 1 is assigned to the Lifeline association group and can add max 5 association nodes. When the PIR motion sensor is triggered, the MultiSensor will send Basic Set (0xFF) to the associated nodes. If no PIR motion is triggered after the PIR interval time (configurable), the MultiSensor will send Basic Set (0x00) to the associated nodes. The automatically reports of temperature, humidity, luminance and ultraviolet (configurable) also can be sent to the associated nodes.

Z-Wave Configuration Capabilities


Parameter Number

Parameter Size

Parameter Name

Parameter Values

100 1 Set the parameter 101-103 to default values. 1 Set the parameter 101-103 to default values.
101 4 To set which report would be sent in Report group 1 128 Luminance Report is enabled.
  1 Battery Report is enabled.
  32 Temperature Report is enabled.
  64 Humidity Report is enabled.
  16 Ultraviolet Report is enabled.
102 4 To set which report would be sent in Report group 2 16 Ultraviolet Report is enabled.
  1 Battery Report is enabled.
  32 Temperature Report is enabled.
  128 Luminance Report is enabled.
  64 Humidity Report is enabled.
103 4 To set which report would be sent in Report group 3 1 Battery Report is enabled.
  128 Luminance Report is enabled.
  16 Ultraviolet Report is enabled.
  64 Humidity Report is enabled.
  32 Temperature Report is enabled.
111 4 To set the interval time of sending reports in Report group 1 5 to 2678400
(Default)
Available rang is 5 to 2678400 seconds.
112 4 To set the interval time of sending reports in Report group 2 5 to 2678400
(Default)
Available rang is 5 to 2678400 seconds.
113 4 To set the interval time of sending reports in Report group 3 5 to 2678400
(Default)
Available rang is 5 to 2678400 seconds.
2 1 Enable/Disable waking up for 10 minutes when re-power on (battery mode) the MultiSensor. 0
(Default)
Disable
  1 Enable.
201 2 Temperature sensor calibration -128 to 127
(Default)
Available rang is -12.8℃ to 12.7℃.
202 1 Humidity sensor calibration -50 to 50
(Default)
Available rang is -50RH to 50RH.
203 2 Luminance sensor calibration -1000 to 1000
(Default)
Available rang is -1000Lux to 1000Lux.
204 1 Ultraviolet sensor calibration -10 to 10
(Default)
Available rang is -10 to 10.
252 1 Enable/disable all configuration parameters to be locked 0
(Default)
Disable
  1 Enable.
255 4 Reset to factory defaults. 1 Reset all configuration parameters to factory defaults.
  1431655765 Reset the product to factory defaults.
3 2 Set the PIR time. 10 to 3600
(Default)
The range of PIR time is 10 to 3600.
39 1 Configure the default low battery value. 10 to 50
(Default)
Available rang is 10% to 50%.
4 1 Set the sensitivity of the motion sensor. 1 Sensitivity Level 1 of 6
  5
(Default)
Maximum Sensitivity
  0 Minimum Sensitivity
  4 Sensitivity Level 5 of 6
  2 Sensitivity Level 2 of 6
  3 Sensitivity Level 3 of 6
40 1 Enable/disable the selective reporting only when measurements reach a certain threshold or percentage 0
(Default)
Disable
  1 Enable.
41 4 Threshold change in temperature to induce an automatic report. 10 to 2120
(Default)
Available rang of threshold is 1℉ to 212℉.
42 1 Threshold change in humidity to induce an automatic report 1 to 100
(Default)
Available rang is 1% to 100%.
43 2 Threshold change in luminance to induce an automatic report. 1 to 30000
(Default)
Available rang is 1 LUX to 30000 LUX.
44 1 Threshold change in battery level to induce an automatic report. 1 to 100
(Default)
Available rang is 1% to 100%.
45 1 Threshold change in ultraviolet to induce an automatic report. 1 to 11
(Default)
Available rang is 1 to 11.
46 1 Enable/disable to send the alarm report of low temperature 1 Enable.
  0
(Default)
Disable
  1 to 30000 Available rang is 1LUX to 30000LUX.
48 1 Enable/disable to send a report when the measurement is more than the upper limit value or less than the lower limit value. 0
(Default)
Disable
  1 Enable.
49 4 Set the upper limit value of temperature sensor. -400 to 2120
(Default)
Available rang is -40.0℉ to 212.0℉.
5 1 Which command would be sent when the motion sensor triggered. 2 Send Sensor Binary Report CC
  1
(Default)
Send Basic Set CC
50 4 Set the lower limit value of temperature sensor. -400 to 2120
(Default)
Available rang is -40.0℉ to 212.0℉.
51 1 Set the upper limit value of humidity sensor. 0 to 100
(Default)
Available rang is 0% to 100%.
52 1 Set the lower limit value of humidity sensor. 0 to 100
(Default)
Available rang is 0% to 100%.
53 1 Set the upper limit value of Lighting sensor 0 to 30000
(Default)
Available rang is 0 to 30000LUX.
54 1 Set the lower limit value of Lighting sensor. 0 to 30000
(Default)
Available rang is 0 to 30000LUX.
55 1 Set the upper limit value of ultraviolet sensor. 1 to 11
(Default)
Available rang is 1 to 11.
56 1 Set the lower limit value of ultraviolet sensor. 1 to 11
(Default)
Available rang is 1 to 11.
57 2 Set the recover limit value of temperature sensor. 10 to 255
(Default)
Available rang is 1.0℉ to 25.5℉
58 1 Set the recover limit value of humidity sensor. 1 to 50
(Default)
Available rang is 1 to 50%
59 1 Set the recover limit value of Lighting sensor. 1 to 127
(Default)
Available rang is 10Lux to 1270Lux
60 1 Set the recover limit value of Ultraviolet sensor. 256 Keep sleep state for Battery power mode
  257 Keep awake for 10 minutes for battery power mode.
  0 USB power mode
  1 to 5
(Default)
Available rang is 1 to 5.
61 2 Get the out-of-limit state of the Sensors. 8 Ultraviolet sensor is out of the lower limit
  32 Humidity sensor is out of the upper limit
  16 Temperature sensor is out of the upper limit
  2 Humidity sensor is out of the lower limit
  4 Luminance sensor is out of the lower limit
  64 Luminance sensor is out of the upper limit
  128 Ultraviolet sensor is out of the upper limit
  1 Temperature sensor is out of the lower limit
64 1 Set the default unit of the automatic temperature report in parameter 101-103. 2
(Default)
The unit is Fahrenheit.
  1 The unit is Celsius.
8 1 Set the timeout of awake after the Wake Up CC is sent out.. 8 to 127
(Default)
Available rang is 8 to 127 seconds.
81 1 Enable/disable the LED blinking when the PIR is triggered. 1 Disable
  0
(Default)
Enable.
9 2 Report the current power mode and the product state for battery power mode 257 Keep awake for 10 minutes for battery power mode.
  256 Keep sleep state for Battery power mode
  0
(Default)
USB power mode

User manual

  • Manual

Guides

  • Guides
More Information
EAN No
Manufacturer Aeotec
Usage Control Lighting, Detect Activity, Monitor Weather
Write Your Own Review
You're reviewing:Aeotec Recessor for Multisensor 6
Your Rating
Copyright © 2016 Swinestudio. All rights reserved.